Boral Flashing Replacement Nationwide

Boral Flashing Replacement: The Fresno Owner’s Guide

Birchbark Roofing Fresno carries and installs Boral-compatible flashing replacement for tile and composite roofs across the Fresno area, with most flashing replacement jobs running $380 to $850 installed depending on penetration type and roof pitch. We keep common Boral flashing profiles on the truck, so a single pipe jack, vent collar, or valley flashing swap is usually done in one visit. Most Fresno homeowners discover the problem the hard way: a water stain on the ceiling after a January storm, or a chalky mineral line running down a wall below the roofline. By the time the stain shows inside, the flashing has usually been leaking for months.

Call (559) 785-9461

Which Boral Models This Applies To

Boral flashing is not one universal part. It is a system of collars, step flashing, and valley metal sized to specific Boral tile and composite profiles: Boral SteelStone, Boral CONCRETE tile, and the discontinued Boral Inspiration and Boral Country Shingle lines all used different flashing geometries. The compatibility gotcha we see in Fresno is this: Boral tile profiles are deeper than standard asphalt shingle profiles, so off-the-shelf step flashing from a big-box store sits too low against the tile and lets water track sideways. The flashing has to match both the profile depth and the butt height of the tile, not just the color.

If you are trying to identify what you have, check the underside of a broken tile for a “Boral” stamp, or look for a code like “BT” (Boral Tile) followed by a profile number on the original packaging if the previous owner left it in the garage. For aftermarket equivalents, we source from flashing suppliers who manufacture to Boral’s original profile dimensions rather than generic “universal” profiles, which almost never seal correctly on a Boral roof. Birchbark Roofing Fresno is an independent roofing company and not affiliated with Boral, but we work with their flashing profiles daily and keep the common sizes in our Fresno inventory.

Signs Your Boral Flashing Replacement Is Failing

• Water staining on ceilings or walls near chimney, vents, or skylights. Flashing at penetrations degrades before the tile or shingle around it. The stain usually appears six to eighteen inches below the roofline, and it is almost always the flashing, not the tile, that let the water in.
• Chalky white or rust-colored residue on the roof deck near pipe collars. Metal flashing in the Central Valley’s heat cycles expands and contracts daily from summer to winter. The seams eventually crack, and dissolved minerals from the water run leave a telltale trail.
• Loose or lifted flashing visible from the ground or a ladder. Strong Fresno winds, especially in the northwest neighborhoods closer to the open valley, can catch flashing edges and work the nails loose over time. If it looks lifted, it is no longer sealing.
• Granules or debris collecting at the base of a valley flashing line. Valley flashing channels more water than any other part of the roof. When the metal gets thin from decades of water flow, small pinholes form and the trapped debris shows where water slowed down and pooled.
• Attic dampness or musty smell in the Tower District homes we serve. Older bungalows in the Tower District have roof decks that dry slowly once a flashing leak starts. By the time it smells in the attic, the leak has saturated the decking at the penetration.

Replacement Cost & What’s Included

In Fresno, most Boral flashing replacement jobs run $380 to $850 installed for a single penetration, like a plumbing vent collar or a bathroom fan flashing. A full valley flashing replacement with new underlayment runs higher, typically $900 to $1,400 depending on valley length and whether the tile around it needs resetting. The spread comes down to three things: roof pitch (steep roofs take longer and cost more), access (two-story homes and tight side yards add labor), and whether the surrounding tile or shingle is reusable or needs replacement.

Your written price from Birchbark Roofing Fresno includes the flashing itself, any replacement underlayment at the penetration, the labor to pull and reset surrounding Boral tile, and full clean-up. No charge for the estimate, no change orders after the fact, and the 365-Day Done Right Promise covers the repair for a full year. If the water comes back for any reason related to our work, we come back and make it right.

DIY or Call Us?

Replacing flashing on a tile roof means working at height on a surface that is brittle and unforgiving. A dropped tile from a second-story eave can break a fence board or worse, and a cracked tile stepped on by an untrained person becomes another leak you will not see until winter. What you can safely do from the ground or a ladder is look and document: photograph the flashing area, note which penetration it is (vent, skylight, chimney), and check the attic from below with a flashlight. If you see daylight at the flashing line from inside the attic, that is the leak.

What goes wrong with DIY is the seal: Boral flashing replacement is not just swapping metal, it is re-bedding the flashing to the tile profile with the right sealant for the Central Valley’s UV and heat, then resetting the tile without cracking the neighbors. We keep the common profiles stocked and can usually have the part matched and installed in one visit. Call (559) 785-9461 and describe what you are seeing; we will tell you what it likely is and get you a written price before we start anything.

FAQs